電壓擊穿試驗儀-安裝條件
50KV電壓擊穿試驗儀 安裝條件：
電源： 220V±10%的單相交流電壓和50Hz±1%的頻率
電源電壓穩定度外界電源電壓波動≤10%
長×寬×高700mm×800mm×1650mm
設備自重： 100kg
運行環境溫度：15 ～ 30℃，相對濕度：30%～85%能夠穩定運行。
接地要求儀器需要單獨接地，接地附合國家標準要求
接地電阻要求≤4Ω（用戶實驗室自行準備）
電壓擊穿試驗儀組成：
1、升壓部件：由調壓器和高壓變壓器組成0～50KV的升壓部分。
2、動部件：由步進電機均勻調節調壓器使加給高壓變壓器的電壓變化。
3、檢測部件：由集成電路組成的測量電路。通過信號線把檢測的模擬信號和開關信號傳給計算機。
4、計算機軟件：通過智能電路把由檢測設備采集的測控信號傳給計算機。計算機根據采集的信息控制設備運行并處理試驗結果。
5、試驗電極：根據國家標準(1408.1-2006)隨設備提供三個電極，具體規格為：Ф25mm×25mm兩個；Ф75mm×25mm一個。（訂做除外）
標簽：
電壓擊穿強度試驗儀
耐電壓強度擊穿試驗儀
電氣強度絕緣試驗機
介電擊穿強度試驗儀
50 kv voltage puncture tester Installation conditions:
Power: 220 v + / - 10% of the single-phase ac voltage and the frequency of 50 hz + 1%
Power supply voltage stability the outside power supply voltage fluctuation 10% or less
Length x width x height of 700 mm * 800 mm * 1650 mm
Equipment weight: 100 kg
Running environment temperature: 15 ~ 30 ℃, relative humidity: 30% ~ 85% can stable operation.
Grounding requires instrument need separate grounding, along with the national standard requirements
Grounding resistance 4 or less Ω (user laboratory prepare)
The breakdown voltage of tester:
1, booster parts: consists of a voltage regulator and the high voltage transformer 0 ~ 50 kv booster section.
2, moving parts: uniform regulation voltage regulator by stepper motor to high voltage transformer voltage change.
3, test parts: measurement circuit composed of integrated circuit.Through the analog signal and the detection line switch signal to the computer.
4, computer software, by testing equipment acquisition through inligent circuit of measurement and control signals to the computer.Computer control equipment operation according to the collected information and process the test results.
5, test electrode: according to the national standard (1408.1-2006) with the equipment to provide three electrodes, specifications are: Ф two 25 mm x 25 mm;Ф a 75 mm x 25 mm.Except (build)
